Bronze Metal

13.00 CHF59.00 CHF

Printing temperature: 200 – 220°C
Can be printed without heating mat (with: 35 – 60°C)
Specific density: 3.39gr./cc.
Traction module: 3990mpa. (Young’s module)
Elongation at break: 8%
Impact resistance (Izod method): 11.3kj./m².
Temp. Vicat softening: 65°C
PLA loaded with 80% bronze
3 x heavier than traditional PLA
“Cold” feeling of metal to the touch
Excellent “printability” with direct or bowden 3D printers
Addition of processing additive for easy and reliable printing
Quick and easy polishing and other post-processing
Possibility to print with withdrawal
Works with ≥0.35mm nozzles.
Low retraction


Bronze Metal is available in 1 color. Samples of 50gr. are available (bronze only). Make your choice!

Bronze Metal is a PLA filament loaded with 80% bronze, easy to print, sand and polish. Create beautiful objects with a true metallic look, a weight 3 x higher than traditional PLA, as well as a touch and thermos-conductivity that brings it closer to metal. Due to the high percentage of bronze, bronze metal has virtually no retraction but adheres a little more to the nozzle. There is a special lubricant that increases the flow and prevents the Bronze Metal from adhering to the nozzle. Finally, all of the above combined with its correct strength, the result is a filament that can be printed on almost all types of filament deposition 3D printers available on the market with removal activated for nozzles ≥ 0.35mm.

Directions for use:
– The recommended temperature for the heating mat is ± 35 – 60°C. Due to its low tendency to retract, Bronze Metal can also be printed without a heating mat. Despite its low tendency to retract, we recommend using a hook like The EZ Stick (for all types of parts), an adhesive such as Blue Tape or PET (for small parts), glue (for large parts), or even both (Blue Tape or PET and glue). If you use glue, no need to put it on the entire surface of the part, but only on the contours or areas at risk of retraction.
– CAUTION, please use a hardened steel nozzle when printing with Bronze Metal. Bronze powder is extremely abrasive and causes rapid wear of the conventional brass or copper nozzles (provide replacement nozzles every 500gr. approximately).
– Please take a look at the “Tips” section for more information on printing and post-processing Bronze Metal.
– Bronze Metal can be used on almost all filament deposition 3D printers.

Storage tips:
– Our filaments are filmed, in a cardboard box without window filmed also to ensure the good conservation of the product until the moment of use.
– Store it in a cold and dry environment (15 – 25 ° C), away from light (UV) and under vacuum (to stay dry). We recommend that, after each use, you vacuum it by slipping a silica gel pouch into it and in its box protected from UV. Good storage significantly increases the shelf life of your filament.

Size Ø Round tolerance
1.75mm. ± 0.05mm. ≥ 95%

Physical properties:
Specific density: ISO 1183 – 3.39gr./cc.
MFR 190°C/2.16kg. : – n.a.
Tensile strength: ISO 527 – 18.3mpa.
Elongation at break: ISO 527 – 8%
Traction module: ISO 527 – 3990mpa.
Impact resistance Izod method 23°C: ISO 180/A – 11.3kj./m².

Thermal properties:
Temp. Printing: DF – 210 ± 10°C
Temp. Melting: ISO 294 – 195 ± 10°C
Temp. Vicat softening: ISO 306 – 65°C


– The range of Metal filaments, such as Copper Metal, Bronze and Brass is very easy to print with any type of nozzle of 0.35 or 0.4mm., although we recommend a spring extruder with a stainless steel (hardened) nozzle. The high percentage of metal in this filament makes it extremely abrasive and leads to rapid degradation of traditional brass or copper nozzles.
– Through extensive testing, we can let you know that the withdrawal does not have to be disabled. However, it is recommended to do some tests beforehand to check if your voltage settings are perfect.
– The tests show excellent results on all Extruders of the Direct, Bowden or Hybrid type.

– Post-processing of the Metal range is a fairly easy process, although manual work is necessary when you do not have access to a sandblasting machine, which gives better polishing results.

Step 1: Print your item.
Step 2: Do a quick brush with a soft brush.
Step 3: Sand with 600 emery paper in water.
Step 4: With a Dremel with a metal polishing wheel, give the object a shiny metal color. Depending on the time and effort spent on step 3 and 4, you will get better results.
Step 5: This step in the process (obtaining a patina) is optional. A future blog will focus on how to get different patinas.

Click here for the technical sheet and finishing tips

Click here for the safety data sheet

Additional information

Weight N/A
Dimensions N/A
Extrusion diameter

1.75 mm.


0.75 Kg., 50 gr.



Availability Now available in-store at
55 route de Chêne Genève 1208

Powered With Oliver Pos


There are no reviews yet.

Show only reviews in English (0)

Be the first to review “Bronze Metal”

Your email address will not be published. Required fields are marked *